Logitech x-530 схема. Hooking up Logitech X

Logitech x-530 схема Rating: 8,7/10 641 reviews

How to Install Logitech X

logitech x-530 схема

When the switch is closed the 6V isn't taken anywhere significant or obvious as far as I could tell. Not only is the holder soldered to the board it is also soldered to the fuse. On occasion when it hits certain frequencies it rattles a tiny bit. Just use the amp or just use the Logitech x-530. Logitech assumes no responsibility for any errors that may appear in this manual.

Next

How to Fix a Dead Logitech X

logitech x-530 схема

The speakers should be on either side of your computer monitor with the right speaker within easy reach, because it houses the system controls. There are 8 screws holding the sub in. If you have a four-channel sound card, connect the green plug from the input audio cable to the front plug of the card and the black plug to the rear plug. Efforts have been made to ensure this page is correct, but it is the responsibility of the user to verify the data is correct for their application. Rear right speaker or pinched particularly a Summary of the content on the page No. You'd be basically just passing the stereo signal through the amp to the Logitech x-530.

Next

Logitech x

logitech x-530 схема

I absolutely love these systems. I suppose I could have used a blade fuse. Then install the 8 mounting screws starting with the one on the bottom. The sub screen has 4 points where it locks in. This is the part that really sucks. If it is not you will have to check the output of the transformer to diagnose the power issue.

Next

How to Connect the Logitech X

logitech x-530 схема

I attached my fuse holder to the port tube with a zip tie to keep it from rattling against something when it was in use. Now that you are done it is time to test. I save the bottom one for last so I can control the sub if it tries to fall out. This warranty gives you specific legal rights, and you may also have other rights which vary under local laws. Step Connect the black plug of the rear right speaker into the black plug on the subwoofer. A small hook pick would be a good tool to use on this to release it. Step Connect the d-sub connector plug from the front right speaker into the d-plug connector on the subwoofer.

Next

Amplifier + Logitech x

logitech x-530 схема

There are dozens of kinds of fuse holders. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. I used a solder wick to desolder the fuse holder. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Logitech X-530 Speaker System X-530. Mine worked just fine after the repair. I should have hot glued it in place.

Next

How to Connect the Logitech X

logitech x-530 схема

This is all the further you need to go anyway. This determines whether or not to allow the speakers and amplifier to work in the Subwoofer. Most times when these die it is the fuse on the board. I will show you how to remedy the fuse problem. Be gentle as it is easy to over heat the pads on the board.

Next

Hooking up Logitech X

logitech x-530 схема

Step Plug the subwoofer power chord into the electrical power outlet. I have recently purchased a samsung le32b652 flat screen lcd tv, and also a set of x-530 speakers which i was recommended by a friend. You do not have to print the entire manual Logitech X-530 Speaker System X-530 but the selected pages only. Get them too hot and they will lift and you will have a nightmare to fix. The Front right speaker controls the inputs and outputs of the system. The Logitech X-530 connects so easily anyone can do it. If colors aren't available, use the labels.

Next

Logitech X

logitech x-530 схема

With any luck you should have a working system now. The guy who told me that might have been crazy? You cannot use the Logitech x-530 as speakers for the amp. You can use any form of fuse you like. Position the left and right rear speakers behind you, making sure they are pointing toward the front left and right speakers. Once you have it soldered in cut off the excess wire and put the controller back in the box and install all the screws. Pull the controller out until the wires running to the power transformer stop you. Position the front center speaker on top of your computer monitor.

Next