Trimmark iie manual. Surveying Equipment

Trimmark iie manual Rating: 7,5/10 430 reviews

Trimble TSC1 Reference Manual

Trimmark iie manual

Insert the 5700 receiver into the backpack with the ports on the top panel facing upwards and the front panel facing outwards. Measuring a Point in Two Faces. For more information, see Configuration Toolbox Software, page 80, or refer to the Configuration Toolbox Help. If you are unsure of restrictions, you are encouraged to ask for authorization before turning on the wireless radio. When you configure the receiver in real time, you use one of these software applications to specify which settings you want to change.

Next

NC Auctions

Trimmark iie manual

On your office computer, open Windows Explorer and navigate to the location of the. The steps required are described below. The level of energyinstructions, may cause harmful interference to emitted is far less than the electromagnetic energyradio communications. Alternatively, you can specify that the power up settings are applied immediately after the current application file's settings have been applied. Insert the controller into the bracket. To view this information, click Radio Info. Saving application files on your computer as well as in your receiver is optional, but it is useful because: · · · it gives you a permanent copy of the settings you have sent to a receiver, for audit or your own reference you can use the same file to configure multiple receivers identically you can use an existing application file as a template for creating other application files with similar settings 54.

Next

Read Trimble R7/R8 GPS Receiver User Guide

Trimmark iie manual

Setting Auto Calibrate to Yes. Unauthorized modification of the units voids the Type approval, the warranty, and the operational license of the equipment. However, if you connect the CompactFlash card to your computer and then copy or move files to your computer, it treats the card like any other disk drive, and transfers the files without converting them. The following recommendations provide optimal performance and extend the life of your batteries: · · · Fully charge all new batteries prior to use. If you click Exit, another screen appears asking you to confirm that you want to quit WinFlash.

Next

Surveying Equipment

Trimmark iie manual

The leading edge is positive, rising from 0 V to 4 V. Whenever the receiver is reset to its factory defaults, the current settings stored in the Current application file, Current. Data is not being logged, or the CompactFlash card is full. Yes Yes No Yes Transfer to Trimble R7? Check that the receiver is using the transferred application file. Starting a Real-Time Rover Survey. Connecting the Base Receiver for a Postprocessed Survey. From the Operation selection dialog, select Configure radio and click Next.

Next

NC Auctions

Trimmark iie manual

Contact your local Trimble Dealer for more information about the support agreement contracts for software and firmware, and an extended warranty program for hardware. The Trimble Survey Controller version 7. To open the door, push the catch on the front panel down. You can run this utility as a standalone program or from within Trimble Geomatics Office. Seat the base of the clip lock in the opposite gate. The values shown are for a one-hour logging session with six satellites visible.


Next

NC Auctions

Trimmark iie manual

When internal or external power is restored, the receiver restarts in the same state as when power was lost. Examine the ports for missing pins. Attach the whip antenna mount to one of the fittings on the top of the backpack. Setting Up the Equipment for a Real-Time Survey. Using a Low Voltage Power Supply. Connect a radio antenna to the external radio.

Next

Surveying Equipment

Trimmark iie manual

Latitude and Longitude Latitude is represented as ddmm. The receiver wakes up five minutes before the scheduled activation time, so that it is ready to begin logging at the scheduled time. Using Windows Explorer, copy the. Fast flash Data is being logged but memory is low. Unknown Instrument Point Coordinates, Several Known Points Surrounding the Instrument Point Resection. Configuring the Receiver in Real Time. Use Adobe Acrobat Reader to view the contents of the release notes.

Next

POB Point & Shoot 2016

Trimmark iie manual

When you need to upgrade the firmware for your Trimble R7 receiver, Trimble recommends that you use WinFlash. Check the charge on the internal batteries and replace if necessary. If there is a timed application file on the Trimble R7, the receiver automatically applies the file's settings and begins logging if logging settings are included in the file at the specified time. Use a multimeter to check pinouts. Trimble Survey Controller To configure your radio network using Trimble Survey Controller: 1. It used to stand alongside a private road as one enters a large tract of mountain land we were surveying in 2007.

Next