Manual vertex ftl 2011. VERTEX FTL

Manual vertex ftl 2011 Rating: 7,2/10 260 reviews

Download Manual Programming Ftl

Manual vertex ftl 2011

I looked for Vertex and Yaesu newsgroups, but none came up. Use the Space bar or Backspace key to increment or decrement this setting, respectively. Your network administrator can advise you of the function of this button if any. Low: The input level is between -44 dBm and -18 dBm. The user is able to hear and respond to all radio traffic, including other hand-helds on the same frequency. I will look on the Vertex site. Two selections are available: 25 seconds or 55 seconds.

Next

Download Manual Programming Ftl

Manual vertex ftl 2011

Installation installed, see near the back of this manual. Reliability is assured by a highly integrated surface mount circuit design and a aluminum extrusion chassis. I've verified the electric connections between the touch button and proc. Files are decompressed supported zip and rar multipart archives Text is extracted from adobe acrobat pdf or plain text documents so that you are able to perform searches inside the files. What a pity it's not one of the versions with a few more channels and the scanning facility.

Next

Vertex FTL

Manual vertex ftl 2011

Case is in used condition, top of heatsink has been repainted as can be seen in the photos. Well-documented service manual available online not included. Trunking Operation 14-1: Trunking This command activates or de-activates the intercommunication protocol for Trunking operation with the connected mobile radio. Also, if you want the radio to scan some channels, I would need to know which ones. When the indicator is off, tone or coded squelch is active.

Next

Vertex FTL

Manual vertex ftl 2011

Note: Although the Squelch Offset range is between 0 and 255, the squelch threshold will be close to saturation if the value is set to about 100 or above. Sorry for all the questions, and hopefully I did not post them in the wrong newsgroup if I did, please point me in the right direction. Adjust the supply voltage to 13. If the audio exits the mobile radio before de-emphasis is applied at the mobile radio side, please set this parameter to On. This allows you to attach a copy of the programming information to the programming work order, for the convenience of the customer. This command allows de-emphasis to be applied or not applied to this audio signal, depending on the condition of the audio signal as it left the mobile radio's receiver section. You can then type in the name you wish to use for this sub-directory, then continue with the file storage process.

Next

FTL

Manual vertex ftl 2011

Otherwise, it may be disabled. Please take a few minutes to read this manual carefully. You may then key their handheld to speak on the voice channel. Connect Wait Time: This is the length of time which the trunked mobile will wait between connection requests to the trunking system. The available values are an arbitrary scale of 0 to 255.

Next

SOLVED: Vertex ftl

Manual vertex ftl 2011

You will need the programming cable plugs into the mic socket. Meantime, thanks for your elaborate explanation regarding the cable. I'm only getting exciter power out of it, too low to read on a regular watt meter. Off: No de-emphasis will be applied to the incoming audio signal. If it is fairly easy to make the programming cable, where can I get instructions on how to do so? LkTn: The Lock Tone system employs audible tone bursts for signalling.

Next

Vertex FTL

Manual vertex ftl 2011

Before turning on the radio the first time, confirm that the power connections have been made correctly and that a proper If the transceiver is not antenna is connected to the antenna jack. If it is cheap enough, I will just buy it. The modes and their corresponding displays are as. I am wanting to use this radio on the 2 meter ham band. Pin 8: Mobile Microphone Audio Mobile microphone audio input. Error Message 2 An external loudspeaker may be connected to this 2-contact, 3.

Next

FTL

Manual vertex ftl 2011

You now have at your fingertips a valuable communications tool a Yaesu two-way radio! These parameters may be modified, if necessary, per the information presented below. Low: The receiver audio level is between36 dBm and -18 dBm. If someone have some ideas or other comments ,please let me know. Note: Any entries or changes made to the Rx Freq. The current data will be read by the computer, and the data will appear on the screen. After reading it, keep the manual handy for quick reference, in case questions arise later on.

Next

SOLVED: Vertex ftl

Manual vertex ftl 2011

But ,i have a big prob ,with the second one. I am wanting to use this radio on the 2 meter ham band. High: The input level is between -18 dBm and 0 dBm. These are parameters shared by all channels. Store this data in a disk file so that it can be saved and retrieved later.

Next

For Sale

Manual vertex ftl 2011

The original software package had you run P4. Ë Select high band edge channel 2. Ë Set the transceiver to the low band edge channel 1. Squelch open: 3 V, Squelch closed: 0 V. These two signals are compared by the phase comparator and applied to the charge pump.

Next