Commander sk advanced user guide manual. Advanced User Guide Commander SK Control

Commander sk advanced user guide manual Rating: 9,6/10 974 reviews

CONTROL TECHNIQUES DIGITAX ST ADVANCED USER'S MANUAL Pdf Download.

commander sk advanced user guide manual

If the feedback is not filtered it is possible the output of the speed controller will be a square wave that changes between the current limits causing the integral term saturation system to malfunction. Orientation mode can always be enabled. If the scan time is greater than the maximum value which may be represented by this parameter the value will be clipped to the maximum value. The output should be routed to Pr 6. Onboard Application Lite Ladder Program is installed and running.

Next

Control Techniques Downloads

commander sk advanced user guide manual

If a value of 12001 is written to Pr x. Processor outputs is drawing too much current. The drive takes action on the command when the user exits the parameter edit mode. These delays allow the motor to stop moving if the test has initiated movement due to cogging torque. The parameters stored in the encoder are in two categories: motor object parameters, and performance object parameters.

Next

CONTROL TECHNIQUES COMMANDER SK ADVANCED USER'S MANUAL Pdf Download.

commander sk advanced user guide manual

This is because a value above 9999 cannot be entered in Pr 5. If this parameter is programmed into the level two area, the decimal place on the drives four digit display will be adjusted to 1 for drive sizes with current ratings greater than 99. The current limit will automatically be reduced therefore only allowing the drive to operate at a lower power rating. Gains Scaling applied Speed controller gains x Source Pr 11. When a destination is changed, the old destination is written to zero, unless the destination change is the result of loading defaults or transferring parameters from a SmartStick. Cannot select any of the 32 bit parameters.

Next

Commander SK Downloads

commander sk advanced user guide manual

Simple installation and configuration making it easy to use but it has the functions required to solve complex applications. This gives the user the flexibility to be able to select between voltage and 3 presets, or current and three presets, with only two digital inputs. Environmental Statement Control Techniques is committed to minimising the environmental impacts of its manufacturing operations and of its products throughout their life cycle. The current limit is set back to the user defined level when the temperature falls below 95%. The following table gives the relationship between the user gain values and the values actually used by the drive. Onboard Application Lite Ladder Program is installed but stopped.

Next

™ sk advanced user Keyword Found Websites Listing

commander sk advanced user guide manual

Ramp rate selection by parameter Pr 1. The values given in the table are the default values. In torque control mode the current demand is limited by the active current limit. If the parameter value reaches 100% an O. In all of the settings below, the status relay is set up as the drive healthy relay. Only bit parameters which are not protected can be set up as a destination.

Next

Commander SK Downloads

commander sk advanced user guide manual

The Motor Control Warehouse was founded in 2006 by three variable speed drives engineers. It is important that this parameter is set up correctly. The product identifier is written to the card. When a new trip occurs all the parameters move down one, the current trip is put in 10. As the torque level is reduced the measurement is likely to be affected by cogging and the results may not be accurate. If this parameter is set to zero these parameters are updated normally. The maximum measurable value for a particular drive size can be calculated from the following formula.

Next

Control Techniques Downloads

commander sk advanced user guide manual

Wait for brake apply frequency 5. The analog output has a resolution of approximately 13 bits ± 1. Power- down save parameters are also saved in the drive when the user initiates a parameter save. This will give a negative value on the analog input destination parameter. When this parameter is set to 1, the fan runs at full speed at all times when the drive is powered up. The rated active current is used extensively to control the drive, and the magnetising current is used in vector mode Rs compensation.

Next

Control Techniques Downloads

commander sk advanced user guide manual

The setting of this parameter configures the terminal for the required mode. Longer pulses should only be used if noise and vibration are a problem and the motor has low friction and low cogging torque. The portable software class which implements this protocol is also defined. The minimum slave response time is times for example, at 19200 baud the minimum silent period is 2ms. If a non-valid parameter is programmed, then the digital output will remain in the inactive state. During the Pre-brake delay period the frequency reference is held constant Pr 2.

Next